BallistiX / FIELD NOTES
Care · Maintenance · Lasting Appearance
Finished interior floor from the BallistiX project gallery The BallistiX Floor Care Guide

How to Maintain Coated Concrete Floors.

Cleaning, protection, and long-term care for the floors you use every day—from residential spaces to working garages and commercial interiors.

01 / Start with the installed system

A protected floor still needs a care routine.

A good maintenance plan starts with knowing what is on the floor.

“Coated concrete” can describe different systems. Your floor may have an epoxy base, decorative flakes, a polyaspartic finish, or a BallistiX topcoat. The exposed finish is especially important when choosing cleaning products and equipment.

Keep the product name, installation date, installer’s contact information, and written care instructions together. If you inherited the floor and do not know the system, ask for help identifying it before changing cleaners or using a machine.

Newly installed? Follow the installer’s cleaning and return-to-service instructions. Being ready for foot traffic does not automatically mean a coating has reached full cure or is ready for every cleaning process.

02 / Make cleaning consistent

Remove soil instead of moving it around.

The routine should fit the traffic and the kind of soil entering the space. A busy workshop needs different attention from a lightly used interior. For BallistiX finishes, begin with the product’s published maintenance instructions.


  1. Remove loose debris first.

    Vacuum, sweep, or dust-mop before wet cleaning, using tools suitable for the finish. Keep the tool itself clean so the next pass does not redistribute collected dirt.


  2. Use the specified cleaning solution.

    Measure the cleaner as directed. More concentrate is not a substitute for the correct process. Work in manageable areas and use the method approved for the installed coating.


  3. Recover the dirty solution.

    Use the approved mop, wet-recovery method, or scrubber procedure to remove loosened soil. Change dirty water and clean tools as needed rather than carrying the same contamination across the room.


  4. Rinse and let the surface dry.

    Follow the product’s rinse instructions and remove remaining soil or cleaner. Keep people away from wet cleaning areas until they are ready to reopen.

03 / Match the tools to the finish

Cleaner strength is only part of the decision.

Compatibility also depends on dilution, contact time, water conditions, and the equipment used. Test a new cleaner or method in a small representative area and review the result before extending it across the floor.

BallistiX Black Label’s published maintenance guidance calls for regular debris removal, cleaning with the specified solution, rinsing, and avoiding red or black pads. Do not apply generic machine-pad advice from another flooring system to your BallistiX finish.

SMOOTH SURFACES

Watch for residue.

Check the result after drying. Persistent streaks or a film may call for reviewing the cleaner, water, and recovery process with your installer.

TEXTURED SURFACES

Clean into the texture.

Soil can remain in a textured finish after a quick mop. Use a compatible brush or approved cleaning process, followed by thorough recovery and rinsing.

04 / Respond to everyday use

Handle spills and changing conditions promptly.

Respond to spills as soon as it is safe. Use a recovery and cleaning method suitable for both the spilled material and the floor. For an unfamiliar chemical, consult the relevant safety information and get appropriate help rather than improvising a cleaner.

After cleanup, inspect the affected area for discoloration, softening, or another visible change. Photograph an unusual spill and record what the floor contacted. That information helps the installer assess whether further attention is needed.

Also review the care plan when the space changes. Turning storage into a workshop, adding vehicle traffic, or introducing a new process can create exposures the original installation was not selected to handle.

Resistance has limits. Avoid leaving chemical puddles on a coated surface. A product’s resistance information applies to defined exposures; it is not permission to leave every substance on the floor indefinitely.

05 / Keep the plan practical

Build a schedule people can follow.

Use this as a planning checklist, then adjust it to the coating’s instructions, traffic, and operating conditions.

When What to review
Each day of use Loose debris, spills, and the cleaning needs created by that day’s traffic.
During cleaning Correct dilution, clean tools, solution recovery, and the required rinse.
After drying Remaining soil, streaks, and any visible changes in the finish.
During inspections Changes near entrances, workstations, joints, and heavily used routes.
After unusual exposure The affected area and whether the installer or technical team should assess it.
06 / Check before restoring

A dull area is a reason to investigate.

Start by checking whether the approved cleaning process removes the visible problem. If a change persists, document its location and contact the installer with the product details and cleaning history.

Do not jump straight to wax, another coating, aggressive buffing, or sanding. BallistiX maintenance guidance specifically cautions against applying other coatings over the surface. Any restoration or recoat needs its own product-specific evaluation and preparation plan.

Common questions

Before you change your routine.

Can I use the same cleaner on every coated floor?

Confirm compatibility with the exact exposed finish. A cleaner or process used on another system is not automatically suitable for yours.

Should I add wax to restore the shine?

For BallistiX finishes, follow the published care guidance instead of adding a wax or coating. Ask the installer to assess a persistent appearance change.

Is a textured floor maintained like a smooth floor?

The tools and recovery process may differ. Textured surfaces can require an approved brush-cleaning method to remove soil from the profile.

When should I contact the installer?

After an unusual chemical exposure, persistent discoloration, visible damage, or a change that remains after appropriate cleaning.

Care for the floor you actually have.

Keep the product instructions close, make the cleaning routine consistent, and ask for guidance before changing the finish.

Find Your Product Documents →
Translate »